MSC flasks and accessories


Description of the parts.



1. The longer casting bottle. Forms a 4-part casting bottle with a diameter of 6 cm (without segment divider) and a height of 7.2 cm. Suitable for e.g. casting of necklaces. Here mounted with 4 cylinder segments (a), segment divider (b), tensioning straps (c) and 3 hose cores (d).


2. The shorter casting bottle. Forms a 4-part casting bottle with a diameter of 6 cm and a height of 3.5 cm. Good to use for e.g. ring molding. Can be combined optionally with the longer bottle (1) or the lid (3). Mounted as the longer bottle, but with only a hose clamp around the strap.


3. Undivided lid. Diameter 6 cm and height 2.8 cm. Can be combined optionally with the MSC bottles. Has no seam, which puts together the lid and the bottom bottle. This makes it much easier when the lid is to be pulled straight up. Masking tape and straps (here fastened around the lid) are used instead. This strap can of course also be used to clamp together two 4-part bottles or other combinations you want to use.


4. Special screwdriver for the hose clamps. Probably the most used tool in the manufacture of the mold.


5. Stand plate in steel, 14 cm in diameter. Serves as a guide of the segments towards the middle when they are pressed together around the model. Marked with concentric circles, lines for the segments and segment numbers.


6. Cone, magnetic at the bottom and provided with a small tip at the top. Works partly as a stand for the model, which is pressed onto the tip (you may need to strengthen the bracket with a little model clay) and partly as a 'model' for a cast, especially important to have when casting in plaster. Can be placed anywhere on the tripod plate, as it is magnetic. Strong magnet made of neodymium, which makes it sit securely on the plate while compressing the segments.


7. Stand for arbitrary placement and orientation of the model. Equipped with several ball joints, adjustable screws and tweezers, which you fasten to the model. This stand also has a strong neodymium magnet in the base, so it sits firmly anywhere on the stand plate. Very valuable for more irregular shapes that can be difficult to orient with the magnetic cone. The stand can of course also be combined with the cone. The tweezers can be placed vertically above the model, which means that the sand segments can be brought together until the model is firmly seated in the bottle. Then the tweezers can be removed and the segments can be completely merged.

An example is shown here (a cobra in attack position). The lid is then used for the part of the cobra that lies against the ground (at the top here)




8. Holder for 2 or 3 sand segments. Good tool in aluminum when you need to hold together sand segments, which is difficult with just your hands.


9. Strong neodymium magnet. Works well as a handle when pulling out, especially the first segment from the model. It is difficult to get a grip on the segment with your hands and a pull-out in the right direction is the most critical step in MSC casting.


10. About 50 cm magnetic tape. Good when casting in plaster, to cover the groove on the inside of the lid. The groove is needed to hold the sand during sand casting


11. Thin plates for casting e.g. rings. It is necessary to place a plate under the model if it is hollow (like a ring) so as not to destroy the segments when they are removed from the model. The diameters of the plates are 13, 18 and 22 mm.


12. Thin steel plate 9 x 1 cm. Good tool to use if you want to place the magnetic cone (6) 'upside down' in any place, e.g. in the lid when casting plaster (which is cast in). See picture below.


MSC Stockholm AB, org. nr. 559233-9245, Folkungagatan 126, lgh 1504, tel. 0760 36 95 95, e-mail: msc.stockholm.ab@gmail.com.Innehar F-skatt, momsreg./VAT-nr. SE559233924501